1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

How to Setup CCcam for ZGEMMA-STAR 2S

Discussion in 'Other Satellite Receivers' started by Herocccam, Sep 5, 2016.

  1. Herocccam

    Herocccam Administrator Staff Member Administrator

    Joined:
    Aug 24, 2016
    Messages:
    347
    Likes Received:
    4
    Trophy Points:
    18
    Gender:
    Male
    Location:
    Herocccam
    Ratings:
    +6 / 0 / -0
    [​IMG]
    STEP 1: INITIAL CABLE CONNECTIONS & SET UP
    • Connect power lead into the back of the receiver.
    • Connect 2 x satellite cables into “Tuner A” & “Tuner B” in the back of the receiver.
    • Connect HDMI/Scart lead into the back of the receiver & other end to TV.
    • Connect Ethernet/LAN cable into “ETHERNET” input on the back of the receiver.
    • The receiver is now ready for configuration.
    • The master power on/off white button is located at the back left hand side of the receiver.

    follow this step: before you go ahead, we direct you the image file and how to save it.
    Insert into the back of the receiver. Do not insert in the front of the receiver as it will not work.
    Press and hold power button at front of receiver. Press the master power button at the back of the receiver to on position. Take finger off the front power button when “FLSH” is displayed on the front of the receiver. Flashing the receiver takes about 4 minutes.
    “BOOT” will then be displayed on the front of the receiver.
    A number count from 1-100 will be displayed on the front of the receiver. When finished receiver will display a channel.
    The receiver is now flashed and ready for the next step. Please remove the memory stick from the back of the receiver.

    Dreambox Control Centre "DCC" to send the line to the receiver. Ensure PC/Laptop has a successful wireless connection to your router. You will require a solid "green" connection from PC-Receiver-Router as displayed in main GUI of DCC)
    Get the IP address of the receiver & gateway via “Menu-Setup-System –Network-Device set up-Adapter settings”. IP & Gateway will be displayed here.
    Open DCC.Change the values in DCC to correspond with the IP of your receiver & router (Gateway) to establish a successful connection. If your laptop is connected wireless to the router the IP address “This computer” will automatically be displayed in DCC. As mentioned above there will be green lines between PC-Receiver-Router if connection has been established.
    Click on “FTP” bottom left of window.
    Click on “ETC”.
    Scroll down & right click on “Cccam.cfg” & left click “edit”.
    Delete whatever is in window if required & copy past your line info here.
    Example C: Host Port Username Password
    Press “Save”. “Cccam.cfg replace, are you sure?” message will be displayed. Choose “yes” option.
    Line has now been sent to the receiver.

    HOW TO CONFIRM THE LINE HAS BEEN SUCCESSFULLY SENT TO THE RECEIVER
    Press the blue button on the remote.
    Choose “Dream Explorer”.
    Choose “Etc”.
    Scroll down and choose “Cccam.cfg”
    If the line has been successfully sent to the receiver via DCC the info will be displayed here. If this area is blank the line has not been sent to the receiver please follow step 4 again.

    STEP 5: MOUNTING THE HARD DRIVE ZGEMMA
    (It is imperative that the following be done within 1 minute of the receiver powering up or the Hard Drive mount will be unsuccessful)
    Turn the receiver off with remote control & power switch at rear.
    Connect the Hard Drive to the USB port at the rear of the receiver (DO NOT CONNECT THE HARD DRIVE TO THE USB PORT AT THE FRONT OF THE RECEIVER, IT WILL NOT WORK!).
    Power up the receiver. When receiver powers up: WITHIN 1 MINUTE:
    Menu – Set up – System = Storage Devices – Initialisation – Press ok on displayed Hard Drive & press red button “Initialise”.
    “Initialising storage device” percentage count will be displayed.
    When finished, via the menu button choose Standby/Restart & restart the receiver.


    STEP 6: SET THE RECEIVER TO AUTOMATICALLY UPDATE
    (In the event of frequency/Channel changes the Z Gemma has the capability to automatically update itself)
    Menu – Set up – Service Searching – “AutoBouquetsMaker” – Configure
    “Setup mode” = Choose expert.
    “Schedule scan” = Yes
    “Time of scan to start” = choose time. Best to set the time AM (e.g. 5AM)
    “Repeat how often” = Weekly option is sufficient but this can be set to daily/monthly if required.
    Press green button “ok” and exit out of all menus.
    THE RECEIVER HAS NOW BEEN SET TO AUTOMATICALLY UPDATE IN THE EVENT OF FREQUENCY CHANGES

    REMOTE CONTROL BUTTON DESCRIPTIONS:
    EPG = Electronic program guide (TV Guide). Located at middle of the remote on right hand side.
    TIMER = Displays programs that are set to record & their status (waiting/done etc). 4th row from bottom, Last button from right hand side.
    FILE LIST = Location of recorded programs. This is where you go to view the programs you have recorded. Located at middle of the remote.
    OK = Whilst viewing a program pressing the ok button will give information on the program.
    UP/DOWN ARROWS = whilst viewing a program pressing the up or down arrow will provide a list of what's currently on other stations.

    HOW TO PAUSE/REWIND ETC LIVE TV
    Whilst watching the program press the pause button (4th row from bottom, 2nd button from right hand side).
    Use the rewind/Forward etc buttons situated around the pause button as is required.

    HOW TO SET PROGRAM/PROGRAMS TO RECORD
    Whilst viewing the program press the record button (4th row from the bottom, left hand side).
    Via the “EPG” button go to the program you want to record & press the record button (4th row from the bottom, left hand side).

    HOW TO SERIES LINK A PROGRAM THAT STARTS AT SAME TIME ON DIFFERENT DAYS
    Via the EPG button go to the program you want to series link
    Highlight the program in yellow & choose "Add Auto Timer "option"
    Use left & right arrows situated at the centre of the remote to change the values below if required. Please only amend the values listed below)

    Timer type” = Record
    Repeat type” = Repeated
    Repeats” = set to “user defined”
    Starting on
    Monday – Friday” set days to yes/no depending what days the program is on
    Start time” Insure time is correct
    End time” Insure time is correct

    HOW TO SERIES LINK A PROGRAM THAT STARTS AT DIFFERENT TIMES DURING THE WEEK
    Via the EPG button go to the program you want to series link
    Highlight the program in yellow & choose “Add Auto Timer “option.
    Arrow down until “Only on Weekday” option is highlighted in yellow and press ok button to remove green tick.
    Press green button “ok” to save.
    Exit from all menus

    HOW TO DELETE A PROGRAM THAT YOU NO LONGER WANT TO SERIES LINK
    Press menu button.
    Choose “Timers”
    Choose "Autotimers "Press "yellow" button to delete & "Green" button to save.
     

Share This Page